Compatible with new hardware

Support EasyScopeX(From V100R001B02D01P21)

1. Optimized communication between SDS1xx4X-E and
SLA1016. This revision (and higher) requires the SLA1016
MUST be upgraded to 8.1.16 (or higher) first. Please take
a look at ‘Compatibility with SLA1016’ at the end of
the release notes.
2. AWG Optimized Bode Plot: Accuracy and Sensitivity
Improvement, New Vari-level Mode for Testing Loop
Response, Miscellaneous Function and UI Improvements.
3. Optimized FFT UI: Added Peaks, Markers, and search
within FFT.
4. Optimized accessing USB drive so that when a USB drive
is moved to a computer, Windows will not prompt a
restoration of the USB drive.
5. Optimize WIFI connection: 63 characters can now be used
for a WPA2 PSK key.
6. Added parity options of MARK/SPACE for UART of 9-bit
Decode.
7. Optimized behavior of the cursors (x-axis): Added a
mode that the cursors remain at the set position on the
waveform when changing time base.

8. Optimize self-calibration for channels. (Recommend to
perform a self-calibration after upgrading.)
9. Added a pop message: If there are too many serial frames
in one sample, the Scope does not decode all of the serial
frames and pop up message of ‘Decoding to maximum
frame number limitation!’
10. Fixed the bug of ROV measurement.
11. Fixed the bug: Normal trigger can show more-than-one
trigger event on the display at one time.
12. Fixed the bug: Erratic triggering, randomly jumping
between the first and the second edge of a signal.
13. Fixe the bug: The acquire time of history is reset to zero
if the time reach 1 hour and 11 minutes. The delta time is
also wrong if the period is longer than 1 hour and 11
minutes.
14. Fixed The SPI triggering issue: the 16-bit trigger wouldn’t
work for a gap >360 ns between the two 8-bit packets.
15. Fixed the bug: Save/Recall setup of trigger and scale
issue.
( SalesForce ID：P-00199) (SalesForce ID：P-00200)
16. Fixed the bug: Reading cursors by SCPI is not accuracy.
(SalesForce ID：P-00201）
17. Fixed the bug: In fine adjust mode, some scale such as
302 mV/DIV is in the wrong position.
18. Fixed the bug: LIN decoder doesn’t decode frames with
zero-length response.
19. Fixed the bug: If the Courser Offset is not a multiple of
zoom time base, the curser will be replaced when
zoomed.
20. Fixed the bug: The measurements made with the cursor
in Ref. Give wrong values for all the different probes of
X1.
21. Fixed the bug: Measures fairs with GATE give completely
random values in signals of low frequency.

1. Added SCPI command to set up gated measurements
and return the data.
2. Customers can save the result of decode list table to a
CSV file.
3. Modified the color of FFT to match the trace selected.
4. There are some times of quick calibration during warming
up the SDS XE. Added a menu below Utility to disable the
quick calibration so that the sampling isn’t interrupted.

5. Created software that converts binary waveform data to
CSV. It can be downloaded from the embedded web
server on the scope.
6. Fixed the bug: “Screen Save” button on web page does
not work with some browsers.
7. Fixed the bug: The setting of Educational mode can’t be
saved after power off.
8. Fixed a bug with MSO decoding. and the SLA1016
firmware also needs to be updated to 8.1.11.
9. Fixed the bug: The binary block returned by the
WAVEFORM command contains the length of the block
in the “#9” header. This length is incorrect when the NP
option of the WFSU command is used; the header then
gives the memory depth instead of the actual size of the
block.
10. Fixed the bug of the scope response from the
WAVEFORM command prefixes the binary block with the
string “ALL,” even when “CHDR OFF” is used.
11. Added exiting the on-screen keyboard by OK button.

1. Initial formal release of SDS1xx4X-E

2. Added Bode Plot support for all of Siglent’ s SDG
instruments
3. Fixed a bug in 6.1.20 which maybe cause the signal
disappear after self-calibration for channels