1. Fixed the bug the attenuation factor is not correct for the SAP1000 probe

1. Supported Power Analysis (optional) (Analysis | Power Analysis)
2. Supported Bode Plot (Analysis | Bode Plot)
3. Supported Totalizer (Analysis | Counter). Frequency and period
parameters are moved from DVM to Counter
4. Supported 2 math traces and formula editor
5. Optimized FFT
a) Optimized menu structure
b) Supported peak and marker (Math | FFT | Tools)
c) Supported setting max points (Math | FFT | Config)
6. Measurement enhanced
a) Optimized the UI. In the “Basic” tab the items can be customized
(long pressing an item to add to or delete from Basic tab)
b) Added items: Median, Cycle median, -Bwidth, Time@max,
Time@min, 20-80%Rise, 80-20%Fall, +Area, -Area, Area,
AbsArea, Cycles, Rising Edges, Falling Edges, Edges, PPulses,
Npulses
c) Supported statistics on maximum 12 parameters at the same time (M2);
d) Optimized measurement accuracy of Rise/fall
e) Supported Trend Plot of measurement items
7. Optimized UX of knobs
8. Set the default function of the universal knob as adjusting the trace
intensity
9. Optimized SPO display
10. Supported moving the location of the decode buses vertically
11. Supported single step back or forward in Navigator
12. Added bandwidth limit indicator below 2.45mV/div (1GHz,
500MHz)/1mV/div(350MHz
13. Supported Zone trigger in Sequence mode
14. Added entry for Zone trigger in the right side trigger menu
15. Mask Test: Supported failed history (Mask Test | Failure to History)
16. Increased frequency setting digits of the AWG from 3 to 7
17. After gesture control of the vertical gain, the v/div knob still is in the
mode that has been used before with the gesture controls.
18. UART/LIN decode/trigger: supported baud rate > 5Mb/s
19. Reference position: Added user defined delay
20. Optimized UI in Zoom mode
21. Deleted the SCPI command which can start Telnet
22. Supported tapping on zone/histogram region to open the
corresponding menu
23. Fixed several bugs

Fixed a bug which may cause failure on installation of option key in 0.9.5R1.

1. Expanded the offset range
2. New serial protocols supported (optional):
   1. SENT, trigger & decode
   2. Manchester, decode only
3. Measurement enhancement:
   1. Supported user-defined thresholds (Upper, Middle and Lower): Measure | Config | Threshold
   2. Added items: +Area@AC, -Area@AC, Area@AC, AbsArea@AC
4. Math:
   1. Added new operator – Interpolate
   2. Added function expression information to the math descriptor box
5. Display:
   1. Supported selectable color for traces: Display | Color Setting
   2. Supported floating menu so that the waveform is not compressed horizontally when the right-side menu is displayed: Display | Menu Style
   3. Supported to hide analog traces
6. Save/Recall:
   1. Added option “Save all channel” for csv file
   2. Supported to save math traces (except FFT)
7. Supported serial trigger as source of the frequency counter
8. Supported LeCroy probes ZD1000/ZD1500 with LPA10 probe adapter; supported Tek TekProbe interface level II probes with TPA10 probe adapter

Added button to reset remote password: Utility | System Setting | I/O | Web

1. Acquire: supported Fixed Sample Rate and Fixed Memory Depth
   modes
2. Connectivity:
   1. Supported LXI
   2. Supported Network Storage
3. Measure: improved the AIM limit from 1,000 to up to 25,000 (AIM limit: the upper limit of horizontal parameters measure statistics in one frame )
4. Power Analysis: supported MOSFET SOA (Safe Operating Area)
5. Channel:
   1. Two custom probe ratio options supported
   2. Supported CP030 current probe (with LPA10 adapter)
6. UX: Added support for mouse wheel when using a mouse
7. Optimized UI
8. Remote Control: Supported to read sequence segments by WF
   command
9. Optimized the Bode Plot
10. Fixed several bugs
    a) Incorrect zoom trace in Roll mode (Stop)
    b) Bode Plot draw error (missing draw)
    c) Bode Plot zig-zag phase
11. [Measure] Gating settings cannot be typed in

1. Supported CAN-H, CAN-L as decode sources
2. Fixed several bugs
   a) Unexpected skew between channels after Stop in Roll mode
   b) Some trigger setting with dual-level may lead the scope not to
   start-up properly

1. Optimized frequency response of 350 MHz model

2. Fixed several bugs

a) Screenshot Save Info Box does not close automatically

b) Random +/-400 ps skew between channels after power cycle

c) No display from Web Server if the scope boots with a USB device connected