1. Solve the problem that the sync signal is
output when the channel is not turned on
2. After the sweep is completed, the output
frequency is modified to stay at the initial
frequency of the sweep.

1. Supported multi-pulse waveform output.
2. Supported sequence playback.
3. Added new “step” sweep mode, and changed the
minimum sweep time to 5us.
4. Added the function of long pressing knob to save
screenshots.
5. Optimized knob response to solve the problem of
occasional code loss.
6. Added SCPI command for synchronous output of two
channels.
7. Added burst hold setting function for burst output.
8. Supported license installation by U-disk.
9. Supported MAC address display.
10. Solved the problem of output error under FSK modulation
when frequency above 300 MHz.
11. Solved the problem of occasional non-response for SCPI
command when connected by socket.
12. Solved the problem of system crash when importing large
CSV waveform file by U-disk.

1. Supports LXI and PWM speed regulation fans.

1. CC status font is red
2. ALL ON/OFF: When the load is on, first close all channels and then press to output simultaneously

1. Solve the problem of output desynchronization when
modulation depth/phase deviation/frequency deviation
is changed in channel tracking mode with AM/PM/FM
modulation
2. Solve the problem of abnormal output waveform when
switching back to the internal clock when the external
reference clock is abnormal.
3. Solve the problem of occasional abnormal output
waveform after power on
4. Add the function of long pressing store/recall to save
screenshots

1. Add an open source declaration
2. Optimize the display of options

1. Optimize Autosetup speed
2. Optimize SDS1104X-E bandwidth
3. Standard software functions of FG, LA and WIFI

Solved some issue on production line

1. Solved the issue where the machine cannot respond to NI-VISA commands after installing the Keysight VIA environment.

CAUTION: This release cannot be downgraded to previous releases.

• 1. Compatible with new hardware
• 2. Supported new probes: SCP5030A/SCP5150/SCP5500, SAP5000D
• 3. Trigger: modified the trigger strategy of /AND and OR trigger from FALSE-to-TRUE to TRUE-to-FALSE
• 4. Acquisition: modified the Average strategy in Single mode from acquiring one frame to acquiring averaged X frames (where X = Average count)
• 5. Optimized UI
  6. Fixed several bugs
  a) Freezing issue in Roll mode
  b) Freezing issue relative to Stop-on-Search-Event in Search mode
  c) In some case the scope does not update the waveform traces after a long time

1. 1. Add the function of long pressing store/recall to save
   screenshots
2. 2. Correct the amplitude deviation problem of ramp
   waveform output
3. 3. Fixed the problem of error prompt when inserting U
   disk
4. 4. Fixed the problem of sync signal output error in
   modulation mode
5. 5. Corrected the problem of abnormal output of small-
   amplitude FM signal
6. 6. Solve the problem of abnormal output when using
   external clock

1. 1. Solve the problem that Bode Plot cannot control sdg1000
2. 2. Solve the problem that user probe coefficient is not restored
   after reboot.
3. 3. Solve the problem that the screen does not support multi-
   touch.

1.Cursor: Supported more cursors, and more flexible cursor combination
2. Measure:
a) Added item UpperLower
b) Supports to zoom in/out Histogram window
c) Supports two units for Histogram vertical axis: Percent, Count
3. Fixed several bugs

1. 1. Supported new probes: Siglent’s SCP5030, SCP5030A, SCP5150,
   SCP5500
2. 2. Measure: Optimized UX of Track and Trend; Supported to export
   measure data
3. 3. Fixed several bugs

• a) Slow response after pressing Math button
• b) AWG: SCPI cannot set Load
• c) Some bugs of USB2.0 compliance test
• d) Some bugs of 100Base-TX and 1000Base-T compliance test
• 4. Some bugs on Options’ unlock

1. 1. Fixed the bug: The average of measurement is mistake for
   35M points
2. 2. Optimized the time of auto-setup

1. 增加支持SigIQPro上位机文件播放功能选件

1. 1. Supported Memory traces: M1 ~ M4
2. 2. Math: supported 4 traces: F1~F4
3. 3. Decode: supported ARINC429
4. 4. Supported USB-GPIB adapter
5. 5. Fixed several bugs
   a) Incorrect time after reboot when time zone = Europe/Rome

1. 1. Optimize the functionality of VNC
2. 2. Optimize the power meter function
3. 3. Solved some bugs
   a) Resolve the issue of insufficient accuracy in saving
   pulse train files
   b) Solved the problem of DAC codeword overflow
   c) Resolve the issue of flatness filling calculation errors

1. Modify the frequency power range limit in mixer measurement
2. Modify the color of the trace title bar to correspond with the color of the memory trace

Fixed an issue in production process.

1. Add pulse modulation function

1. Increased the data width of saved Average and ERES data from 8-bit
to 16-bit
2. Decode: added ARINC429
3. Math: added RBW display for FFT
4. Supported 12-hour time with AM and PM
5. Remote control:
a) Supported the USB-GPIB adapter
b) Added command supporting to query average count when
Acquisition = Average
c) Added command supporting to enable/disable axis labels
6. Fixed several bugs
a) Incorrect prompt when saving .csv with “Save all channels” to a
U-disk as specified file name
b) Channel ON / OFF labels are inconsistent
7. Freezing issue caused by command CURSor:XDELta?

• 1、Add function of IQ stream
• 2、Add function of IOT ,include Zigbee and Z-wave
• 3、Add pause key at sweep mode .
• 4、Add unlock “REMote” command “ :SYSTem:REMote 0”
• 5、Optimize function of IQ

1. 探头系数为10X，通过指令设置trigger level，指令设置的值在机器端相应会增加10倍
2. 客户反馈C4-C1:MEAD? FRR指令异常
3. 在示波器使用U盘后在Win10电脑会提示故障需要扫描修复
4. CSV未考虑探头系数
5. 某些情况下，UART解码异常
6. Ref问题：先打开Ref，再打开single模式采集波形的时候Ref波形消失
7. 通过socket发送pnsu+二进制数据导致机器卡死

1. 兼容G版本硬件
2. 解决频率计开启后卡死问题

1. Fix the issue where static IP cannot be saved

1. Fix the issue where static IP cannot be saved

Revision History

1.优化VGA配置

和SLA1016的各版本兼容性

Upgrade Guide

21. 重要

6.1.33版本优化了通道自校正，从低版本升级完成后，重启机器，要执行一次自校正。

21. 非常重要

因为优化了SDS1xx4X-E和SLA1016的通信，如果要升级SDS1xx4X-E到6.1.33，则必须首先升级SLA1016到8.1.16（或更高），SDS1xx4X-E使用6.1.33以下版本；然后再升级SDS1xx4X-E。

21. 非常重要

6.1.20R1版本解决了通道自校正的一个bug，因此从低版本升级到6.1.20R1（或大于），升级完成后，重启机器，要执行一次自校正。

1. Added Multi-Device mode, supporting automatically skew calibration

Upgrade Guide
between devices

2. Fixed some serious bugs in Zone Trigger, serial trigger and Mask test>

3. Fixed several bugs>

1. Add user manual calibration and verification function (optional)
2. Increasing the number of vertical grids allows for the setting of functions
3. Add vertical axis support for logarithmic display function
4. Add point limit function

1. 解决特定配置下脉冲输出错误的问题
2. 新增幅度扫描功能
3. 新增调节通道 skew 功能
4. 文件管理器增加多文件操作
5. 优 化 sequence 播 放 （ 数 字 通 道 暂 不 支 持 sequence）时波形数据的存储策略
6. PRBS 速率支持到 625Mbps
7. 解决波形切换等情况下输出异常波形的问题

1. Add scalar mixer measurement function
2. Adjust and optimize the spectrum analysis measurement interface

1. 1. Optimized frequency response of 350 MHz model
2. 2. Fixed several bugs
   1. a) Screenshot Save Info Box does not close automatically
   2. b) Random +/-400 ps skew between channels after power cycle
   3. c) No display from Web Server if the scope boots with a USB device
      connected

1. Compatible with new EEPROM chips

1. Compatible with new hardware

1. 1. Measurement enhancement – Added setup/hold time: tsu@R, tsu@F,
   th@R, th@F
2. 2. Optimized UI
3. 3. Added SCPI commands for Measure Cursors and clearing measure
   items in Simple mode
4. 4. Supported LXI (only with the Uboot-OS Version 5.4)
5. 5. Supported time zone setting
6. 6. Fixed several bugs
   a) Webserver doesn’t show instrument UI if the scope reboot with a
   wireless mouse connected
   b) Incorrect “Recall”icon in the File Manager
   c) Scope freezes with AWG enabled and measure cursor on rise
   time
   d) IP setting of AWG in Bode Plot not remembered after reboot
   e) Network storage only works for SMB1.0
   f) MEAS:SIMPle:ITEMsOVSN,ON does not work as expected
   g) Roll time incorrect at 1ks/div and 20kpts
   h) Raw data not consistent in x and sinx/x interpolation modes
   i) Math: Dx parameter of Derivation cannot be increased by
   universal control
   j) Incorrect FFT sample rate

1. Fixed the bug that startup occasional failures
2. Fixed the bug of burst sync output exception
3. Fixed the bug that may not output when switch
   the waveform after the burst is turn off

Fixed the problem: The skew of the two ADCs is not
accuracy for hardware of 09 version (System Status shows
Hardware Version: 09-xx). The other hardware version has
no this problem.

1. Fixed the problem: very few SDS1xx4X-e stuck at self-
   calibration
2. Be Compatible with a new VGA chip

1. Fixed the bug in 6.1.37R2 which cause the WiFi does not
work

1. 1. Added data logger featuring Sample and Measurement
   Logger functions
2. 2. Added counter function
3. 3. Added Labels
4. 4. Added NTP (Network Time Protocol) and Time Zone. Also
   requires OS update to SDS1xx4X-E_OSV2 which is located
   on the SIGLENT product webpage. The OS Update
   Instructions is also included SDS1xx4X-E_OSV2.zip
5. 5. Modified negative or positive of horizontal delay: Time
   zero is in trigger. Before trigger, time position is -time
   (negative delay relative to trigger) and after trigger is
   +time (positive delay relative to trigger)
6. 6. Fixed a bug with Bin2CSV for ROLL mode
7. 7. Rebuilt Bin2CSV to File Converter which can also convert
   data logger file to CSV.
8. 8. Fixed a bug: some case there is a blue line on decode bus
9. 9. Fixed a bug with saving hex MSO CSV file
10. 10. Fixed a bug: After rebooting , Bode Plot cursor can’t be
    moved
11. 11. Fixed a bug: fine adjusting with customer probe
12. 12. WiFi supported Spaces and Special Characters

1. 1. Added support for the SAG1021I USB Isolated AWG
   Module Hardware
2. 2. Fixed the bug: Sometimes PNSU command returns invalid
   value (Need referring to the latest Program Guide)
3. 3. Added 9 data bits for UART decoding
4. 4. Fixed the bug of UART decoder with some special
   settings
5. 5. Increased baud rate of UART trigger from 5 Mbps to 20
   Mbps
6. 6. Fixed the bug: The command ‘WF? DAT2’returns error
   length of waveform when digital is enable
7. 7. Fixed the bug: CSV file of waveform has no indication of
   the trigger point in the data
8. 8. Fixed the bug: After repowering all FFT markers are on
   just one peak
9. 9. Fixed the bug: After repowering, signal level of CAN
   trigger can’t be recalled
10. 10. Fixed a few SCPI Commands errors:
    MATH: CURSOR_VALUE?
                 C3:INVERT_SET? is missing
    HISTORY_LIST? is missing
                 DIGITAL:LOW8_SWICHT, typo in name
                 C5:COUPLING? typo in name
11. 11. Fixed the Bode Plot bug: Sometime there isn’t enough
    delay after the scope switches timebase values before it
    tries to take a measurement
12. 12. Fixed the bug ： Matlab can’t import 14 M Matlab
    waveform files
13. 13. Fixed the bug：‘WF?’command ignores the length set
    by ‘WFSU’ for digital