SIGLENT, 67GHz 지원 제품 및 다채널 솔루션으로 마이크로파 신호 발생기 포트폴리오 확대
New SSG6089A extends frequency coverage to 67 GHz, while the SSG6M80A series introduces phase-coherent signal generation with two or four channels up to 20 GHz.
As wireless communication systems and high-frequency electronic applications continue to evolve, the requirements placed on RF test and measurement equipment are becoming increasingly demanding. Higher operating frequencies improved spectral purity and the ability to generate multiple precisely synchronized signals are important factors in the development and verification of modern electronic systems. Applications such as 5G/6G research, satellite communications, multi-antenna systems require signal sources that combine frequency coverage, signal quality and flexible configuration.

To address these requirements, SIGLENT Technologies is expanding its microwave signal generator portfolio with two product introductions: the SSG6089A microwave signal generator, extending the existing SSG6000A series to 67 GHz, and the new SSG6M80A series, providing two or four phase-coherent RF channels with frequencies up to 20 GHz
SSG6089A – Extending Microwave Signal Generation to 67 GHz
The new SSG6089A expands the frequency range of SIGLENT’s established SSG6000A series, which previously covered frequencies up to 40 GHz. With a frequency range from 100 kHz to 67 GHz, the instrument addresses applications requiring signal generation in higher microwave and millimeter-wave frequency bands.
The SSG6089A provides a frequency setting resolution of 0.001 Hz and supports analog amplitude, frequency and phase modulation. Frequency and amplitude sweeps, optional pulse generation and power meter control enable its use in a variety of RF measurement applications.
In addition to the extended frequency coverage, SIGLENT introduces options for increased RF output power and reduced phase noise. The optional high-power configuration provides output levels of up to +30 dBm in selected frequency ranges, allowing higher signal levels to be generated without additional external amplification in suitable applications.
The optional low-phase-noise configuration improves signal purity, particularly for measurements sensitive to oscillator phase noise. With the SSG6080A-LPH2 option, the series achieves typical phase noise performance of -149 dBc/Hz at a 1 GHz carrier frequency and 10 kHz offset.
These capabilities make the SSG6089A suitable for applications including microwave component characterization, receiver testing and research into next-generation wireless communication technologies.
SSG6M80A – Phase-Coherent Multi-Channel Signal Generation up to 20 GHz
Alongside the extension of the SSG6000A series, SIGLENT introduces the SSG6M80A series of multi-channel microwave signal generators.
The new series is available with two or four RF channels and frequency ranges from 9 kHz to either 13.6 GHz or 20 GHz, depending on the model. Each channel can be configured independently in frequency, amplitude, phase and time delay.
A central feature of the SSG6M80A series is its phase-coherent architecture, supporting phase coherence between channels within a single instrument as well as across multiple synchronized instruments. This enables the generation of multiple RF signals with defined phase relationships, an important requirement in applications such as phased-array systems, beamforming, MIMO testing and multi-channel receiver evaluation.
The generators provide a frequency resolution of 0.001 Hz, phase adjustment resolution of 0.1° and typical phase noise of -135 dBc/Hz at a 1 GHz carrier frequency and 10 kHz offset.
Additional capabilities include analog frequency and phase modulation, optional pulse generation and pulse sequence functionality. An integrated OCXO reference
supports frequency stability, while power meter control facilitates output level adjustment and compensation for external signal path losses.
Designed for Laboratory and Automated Test Environments
Both product families provide USB and LAN interfaces for remote control and integration into automated test systems, with GPIB available as an option. Their 5-inch touchscreen interfaces support local instrument configuration and operation.
With the SSG6089A and SSG6M80A series, SIGLENT addresses two different requirements in modern RF testing: extending signal generation into higher frequency bands and providing multiple phase-coherent signals from a compact instrument platform.
The new generators complement SIGLENT’s existing RF test and measurement portfolio and are intended for use in research and development, system verification and production testing.
SIGLENT Technologies celebrates the grand opening of its new North American operations center in North Plains, Oregon.
Siglent Technologies continues investing in global capabilities and partnerships that support our customers across the world with the grand opening of our new North American operations center in North Plains, Oregon. Our new North American operations center in North Plains, Oregon includes over 13,000 square feet of space including sales and support offices, a new calibration and service center, and warehousing.

In 2014, Siglent established subsidiaries in the US and Germany followed by Japan in 2022. These regional offices support customers around the world with the quality, capability, and value that Siglent is known for. In 2025, Siglent established a full-process production facility in Penang, Malaysia that manufactures instruments for our global customers.
“This year, our new investment in US capabilities will lay the foundation for years of future growth while providing engineers with access to solutions for their everyday measurement challenges.” says Mike Rizzo, Siglent USA General Manager.

Siglent continues to grow aggressively, providing test and measurement solutions to customers from education to semiconductors. This new operations center will enable us to support even more engineers as we continue a period of strong growth and lay the foundation for an even stronger future.

From oscilloscopes and function generators to spectrum and network analyzers, SIGLENT is a global leader in the design and manufacture of electronic test and measurement instruments that provide high accuracy data, dependable quality, and a smart user interface at prices that deliver value for many years.
.
.
Siglent, 고정밀 RF 테스트에서 뛰어난 신호 순도와 안정성을 구현하는 SSG3000X Plus 시리즈 RF 신호 발생기 출시
Siglent launches the SSG3000X Plus Series RF signal generators. Covering a frequency range of 9 kHz to 3.2 GHz with maximum output power of +20 dBm, the series features an optional high-stability OCXO reference source, excellent phase noise, and significantly improved pulse signal fidelity, delivering pure signal output and stable performance.
The SSG3000X Plus comes standard with AM/FM/PM analog modulation, pulse modulation, and USB power meter control. It supports custom pulse sequences and external IQ modulation, and is equipped with a 5-inch capacitive touchscreen. The SSG3000X Plus is well suited for RF component characterization, research and development, manufacturing, education, and maintenance applications, providing a pure, stable, and competitively priced professional RF signal solution.
옵션인 고정밀 OCXO 레퍼런스 소스는 주파수 안정도를 크게 향상시켜, 온도 안정성을 높여주고 경년 변화율을 낮춰줍니다. 따라서 온도 변화와 장시간 작동에 따른 주파수 드리프트가 줄기 때문에 장시간 테스트를 진행하는 고정밀 부문의 엄격한 정확도 요건을 충족하며, 신호 출력의 장시간 신뢰성도 보장합니다.

위상 잡음 성능이 1GHz 반송파(20kHz 오프셋 포함)에서 -117dBc/Hz(일반) 이상이며, 광대역 잡음은 일반적으로 40MHz 오프셋에서 -153dBc/Hz 이상입니다. 고조파 및 비고조파 억제 성능이 넓은 주파수 범위에서 뛰어나 고정밀 수신기 테스트 및 고감도 측정 시 결과가 정확하고 안정적으로 나옵니다.

표준 AM/FM/PM 아날로그 변조는 내부 소스, 외부 소스, 내부 + 외부 변조 소스를 지원합니다. IQE 모델에서 사용할 수 있는 외부 IQ 변조는 외부 I/Q 입력으로 구현됩니다. SDG6000X 기저대역 소스와 페어링하면 16QAM 및 QPSK 같이 RF 변조 대역폭이 200MHz인 벡터 신호를 발생할 수 있어, 복잡한 디지털 변조 신호 발생에 필요한 요건을 충족합니다.

펄스 변조는 일반 상승/하강 시간이 15ns 미만이며 온/오프 비율은 최대 68dBc입니다. 펄스 파형이 더 평탄해 파워 증폭기나 T/R 모듈 같은 장치가 손상될 위험이 그만큼 적습니다. 단일 펄스 모드, 이중 펄스 모드, 최대 펄스 2047의 펄스 시퀀스 모드(옵션 PT)가 지원되고, 펄스 폭과 주기를 정밀하게 조정할 수 있어 펄스 장비 테스트 요건을 충족합니다.

5인치 정전식 터치스크린에 마우스와 키보드가 지원되어 직관적으로 조작할 수 있습니다. 최대 65,535개 포인트를 지원하는 스텝 및 리스트 스윕 기능에 여러 트리거 모드를 함께 사용할 수 있어 주파수 및 레벨 스윕이 빠릅니다. 내장된 USB 파워 미터 제어 기능이 케이블 손실과 온도 드리프트를 자동으로 보상합니다. USB, LAN, 옵션인 GPIB 인터페이스와 함께 웹 원격 제어 기능을 사용하여 자동화 테스트 환경에 원활하게 통합할 수 있습니다.

The SSG3000X Plus series RF signal generators, designed to deliver exceptional signal purity, stability, and versatility for precision RF testing. The new series enhances frequency stability, phase noise performance, and pulse fidelity while offering comprehensive modulation capabilities and intuitive operation. Ideal for RF component characterization, research and development, manufacturing, education, and maintenance, it provides a pure, reliable, and cost-effective professional solution.
Siglent Releases SigVSA Vector Signal Analysis Software
Siglent officially launched the next-generation SigVSA Vector Signal Analysis Software, bringing professional vector signal analysis capabilities to engineers’ desktops. Compatible with both Windows and Linux operating systems, the software enables comprehensive measurements ranging from basic BPSK signals to complex wideband signals (e.g., UWB, LTE, 5G NR and 4096QAM), delivering an efficient, flexible and unified signal analysis platform for the R&D, testing and manufacturing of wireless communications.

SigVSA offers two application forms: Desktop and Embedded, supporting full-process collaboration from R&D to production. The Desktop version runs on PC, breaking the limitations of instrument hardware and providing a flexible operating environment for complex wideband signal analysis. The Embedded version is deeply integrated into Siglent oscilloscopes and spectrum analyzers (e.g., SDS7000A with the RFA option), enabling high-precision signal analysis without an external PC and simplifying test setups. Both versions share a consistent user interface and measurement engine, ensuring a seamless operational experience.
SigVSA boasts rich measurement functions, currently supports mainstream wireless communication standards including 5G NR/NR-A, 5G NR-NTN, LTE/LTE-A FDD/TDD, Wi-Fi 802.11 a/b/g/n/ac/ax/be, Bluetooth, HRP-UWB and FHSS signals. Signal analysis functions for NB-IoT, GSM, WCDMA, DVB-S2/S2X and FMCW will be launched successively. SigVSA supports synchronized multi-device acquisition and analysis, allowing remote control and waveform capture for up to 32 instruments simultaneously. Equipped with remote management capabilities, it enables one-click device configuration switching, automatic connection record saving, and configuration synchronization from the host to the analyzer. Its multi-window display and custom layout features further enhance the efficiency of parallel multi-task analysis.
SigVSA provides comprehensive local analysis capabilities, supporting direct import and analysis of raw waveform files from analyzers for flexible offline signal evaluation. Additionally, SigVSA enables remote signal analysis and debugging on a PC, allowing simultaneous control of multiple instruments to acquire and process signals, without relying on the instrument’s vector analysis options, expanding its applicability and device compatibility. With SigVSA, engineers can tackle various signal analysis challenges more freely and efficiently.
Siglent has launched attractive promotional policies and flexible licensing plans, greatly lowering the barrier to use. From June 22, 2026 to June 22, 2028, purchasing an SDS7000A oscilloscope with the RFA option will receive full-feature of Embedded SigVSA free of charge, enabling complete high-end signal analysis functionality. Furthermore, the SigVSA PC version is available for free download, with the base version including three core functions: Spectrum and IQ Analysis (SIGV-VSAA1), Digital Modulation Analysis (SIGV-VSAD1), and Custom OFDM Modulation Analysis (SIGV-VSAO1). TRY BEFORE YOU BUY! Confident in its performance, SigVSA offers 30 free trials for each function, enabling you to evaluate its powerful analysis capabilities risk-free. Start testing today to find your perfect solution.

Click To Check the Promotion Details
The release of SigVSA enriches Siglent’s signal analysis platform. Together with Siglent signal generation software SigIQPro, it forms a complete solution from signal generation to analysis, supporting engineers in accurately simulating real-world communication scenarios and enabling a smooth transition from traditional tools to a modern, scalable platform. Going forward, Siglent will continue to iterate SigVSA’s features, expand its signal analysis coverage, and provide higher-quality solutions for wireless communication testing.
SIGLENT Launches 8 GHz Active Differential Probe for High-Speed and RF Applications
SIGLENT introduces the SAP8000D Active Differential Probe, designed to address the challenges of high-speed signal characterization and RF testing.
Featuring 8 GHz bandwidth and ultra-low 300 fF input capacitance, the SAP8000D minimizes probe loading effects while preserving signal integrity in demanding measurement environments. The probe supports both differential and single-ended measurements and provides high common-mode rejection for improved measurement accuracy.
The SAP8000D is well suited for high-speed serial bus validation, signal integrity analysis, and high-frequency circuit debugging across applications including PCIe, DDR, USB 3.0, and Gigabit Ethernet.
To accommodate a wide range of test setups, the probe supports multiple probing methods, including solder-in, handheld, and fixture-based configurations, and is compatible with various probe accessories. This flexible design enables engineers to perform reliable measurements in complex test environments with greater confidence.
By combining high bandwidth, low input capacitance, and versatile connectivity options, the SAP8000D provides an effective solution for next-generation high-speed and RF measurement challenges.




SIGLENT, SDG8000A 시리즈 출시: 고성능 RF 및 임의 신호 발생의 새로운 플랫폼
The new Arbitrary Waveform Generator Combines RF Signal Generation, IQ Modulation and Advanced Sequencing in a Single Platform
SIGLENT Technologies announced the launch of the new SDG8000A Series Arbitrary Waveform Generators, a high-performance signal generation platform designed for advanced RF, wireless communication, semiconductor and high-speed digital applications.
As modern communication and RF systems continue to increase in complexity, developers require signal sources capable of generating wideband, highly dynamic and realistic signals with exceptional fidelity. The SDG8000A Series was developed to address these requirements by combining wideband arbitrary waveform generation, direct RF signal synthesis, IQ vector signal generation and advanced sequencing capabilities in a single instrument platform.
The SDG8000A Series delivers in IQ-Mode output frequencies up to 5 GHz with sampling rates up to 12 GSa/s (interpolation) and 16-bit vertical resolution. Available in two- and four-channel configurations, the new platform provides up to 4 Gpts waveform memory per channel, enabling the generation of long and highly complex signal scenarios for modern RF and communication development.
Using SIGLENT’s TrueArb technology, arbitrary waveforms can be reproduced point-by-point while maintaining waveform detail and low jitter performance. The architecture supports narrow pulse generation down to 250 ps and provides advanced multi-pulse functionality for demanding applications in RF, semiconductor and power electronics development.
A key capability of the SDG8000A Series is its integrated RF and IQ signal generation architecture. The internal digital modulator enables direct RF output up to 5 GHz without requiring external IQ modulation hardware. Combined with the optional SigIQPro software package, the system supports signal generation for modern communication standards including 5G NR, LTE, Wi-Fi, Bluetooth and IoT applications. With modulation bandwidths up to 2 GHz, the platform is well suited for RF front-end validation, receiver testing, amplifier characterization and wireless communication development.
The new series also integrates advanced signal creation capabilities such as multi-tone, chirp and PRBS signal generation, as well as high-speed serial data output up to 1.25 Gbps. Its multi-level sequence architecture enables the creation of highly dynamic and realistic signal environments for burst communication, interference simulation and system-level testing applications.
For synchronized multi-channel systems, the SDG8000A Series provides inter-channel skew below 15 ps together with differential output modes, marker outputs, external clock synchronization and advanced triggering capabilities. These features make the platform suitable for MIMO and other synchronized RF test environments.
The SDG8000A Series further supports LAN connectivity, WebServer-based remote control and integrated SSD storage, enabling efficient integration into automated test systems and modern laboratory environments.
About Siglent:
SIGLENT TECHNOLOGIES began in 2002 with the development of its first digital oscilloscopes. Since then, the company has rapidly expanded its portfolio to cover a broad range of general-purpose electronic test and measurement instruments, including oscilloscopes, signal and function/arbitrary waveform generators, digital multimeters, laboratory power supplies, electronic DC loads, spectrum analyzers, vector network analyzers (VNAs), and RF signal generators.
With the introduction of the Performance Line Series in 2021, SIGLENT further advanced its technical capabilities to address demanding applications in high-performance measurement environments, including solutions reaching into the microwave frequency range up to 40 GHz.
Today, SIGLENT TECHNOLOGIES is a globally recognized provider of electronic test and measurement equipment, combining innovative features, strong engineering expertise, and reliable performance. Headquartered in Shenzhen, China, with international subsidiaries in the United States, Germany, Japan, and Malaysia, SIGLENT supports customers in more than 80 countries worldwide.
SIGLENT is certified according to ISO 9001:2015 and ISO 14001:2015 standards, reflecting its commitment to consistent product quality and responsible environmental management.
SIGLENT Launches DPB6150 & SDP6150 Series High-Voltage Differential Probes
SIGLENT launched two new high-voltage differential probes: DPB6150 Series and SDP6150 Series, further enhancing its product portfolio in the power electronics testing domain. Specifically engineered to tackle the challenges of precise power measurements in high-noise environments, these probes leverage exceptional dynamic range and superior common-mode noise rejection capabilities to significantly improve the accuracy and reliability of signal measurements in high-voltage, high-noise conditions. They will become indispensable tools for engineers during the development and testing of switching power supplies, frequency converters, new energy systems, and various power electronic devices.

The DPB6150 and SDP6150 Series high-voltage differential probes feature a maximum bandwidth of 400 MHz and can measure voltages up to 1500 V. With excellent common-mode noise rejection, high input impedance, and low input capacitance, they enable precise measurement of differential voltage signals and floating signals. Equipped with one-touch zero calibration and audible-visual overload alarms, these probes ensure operational safety and convenience, making them widely applicable to R&D and maintenance of switching power supplies, electronic ballasts, variable-frequency appliances, and other electrical power devices.
DPB6150 & SDP6150 Electric Specifications

Siglent Launches SNA5000X-E Vector Network Analyzer
Compact, Cost-Effective 6.5 GHz VNA Delivering High Performance for R&D and Production
Siglent Technologies officially announces the release of the SNA5000X-E Vector Network Analyzer, a compact and cost-effective solution designed to meet essential RF testing requirements without compromising performance. Covering a frequency range from 9 kHz to 6.5 GHz and delivering a typical dynamic range of 125 dB, the SNA5000X-E provides accurate, reliable measurements for R&D, education, and production environments.
Positioned as an entry-level model within the SNA5000 series, the SNA5000X-E retains the core performance architecture of the SNA5000A family while offering enhanced cost-effectiveness for standard vector network analysis applications. It supports 1 Hz frequency resolution, adjustable IF bandwidth from 1 Hz to 10 MHz, and an output power range from –40 dBm to +10 dBm. With its 125 dB typical dynamic range, the instrument maintains excellent measurement stability and accuracy even in complex RF test scenarios.

The SNA5000X-E supports comprehensive S-parameter and differential measurements, along with integrated time-domain analysis, enhanced time-domain analysis, and spectrum analysis functions. These capabilities enable engineers to evaluate frequency-domain characteristics, analyze impedance discontinuities, and quickly locate faults within devices under test. A built-in eye diagram function further supports high-speed signal integrity analysis, improving debugging efficiency during development.

To address fixture-induced measurement errors commonly encountered in RF testing, the SNA5000X-E incorporates automatic fixture removal, port extension, de-embedding, and impedance conversion functions. These tools effectively compensate for cable delay and loss, minimizing systematic errors and ensuring high confidence in measurement results.
Designed for modern laboratories and production lines, the SNA5000X-E features a compact form factor with an instrument depth of only 12.6 cm and a weight of less than 5.4 kg. This significantly reduces workspace requirements compared to traditional network analyzers. The instrument is equipped with a 12.1-inch touchscreen that supports multi-window display and multiple data formats, creating an intuitive and efficient operating experience.
For production and automated test environments, the SNA5000X-E offers one-click filter characteristic analysis to quickly obtain key parameters such as insertion loss and bandwidth. It also supports custom formula operations and remote control via SCPI and WebServer, enabling seamless integration into automated systems and helping standardize and streamline testing workflows.
By returning to the fundamentals of vector network analysis, the SNA5000X-E combines essential performance, intelligent operation, and compact design in an economical solution. It provides a reliable, one-stop platform for applications ranging from R&D validation to batch quality inspection, enabling engineers to achieve professional RF measurement capability with optimized investment.
SIGLENT, SMM3000X 시리즈 소스/측정 유닛 출시
February 27, 2026 — SIGLENT Technologies releases SMM3000X Series Source/Measure Unit (SMU). SMM3000X features 6½-digit resolution, output capability of up to ±210 V DC voltage, ±3.03 A DC current, and ±10.5 A pulsed current, with programming and measurement resolution down to 10 fA / 100 nV, and a maximum acquisition rate of 100,000 points/s.
The SMM3000X supports four-quadrant operation, enabling simultaneous sourcing and measurement for closed-loop source–measure operations on DUTs. It can function as a voltage source, current source, voltmeter, ammeter, and ohmmeter, and also supports pulse generation and arbitrary waveform output, making it an ideal platform for characterizing semiconductors and other nonlinear devices and materials.
High-Accuracy Pulse Simulation
In pulse mode, the SMM3000X series supports pulsed current output up to ±10.5 A, with a minimum pulse width of 50 μs. This allows precise emulation of transient operating conditions of power devices, such as switching loss testing for GaN and SiC devices, providing strong support for R&D and validation of wide-bandgap power semiconductors.

Linear and Log Sweep Functions
The SMM3000X supports linear, log and pulsed sweep modes. Users can define start and stop values with fixed step sizes to source voltage or current point-by-point, while automatically measuring and logging each data point. This enables fast characterization of devices such as diodes and transistors, allowing engineers to extract I-V curves and analyze conduction behavior under different operating conditions.

Flexible User-Defined Sequences
List mode allows users to define custom output sequences with minimum timing resolution down to 10 μs. Parameter changes can be linear, non-linear, arbitrary, or user-ordered. The SMM3000X outputs voltage or current according to the defined list while synchronously measuring and recording data—ideal for non-uniform sweeps, multi-segment tests, and complex stimulus profiles.

Data Visualization and Analysis
The SMM3000X series provides multiple display modes including Graph, Roll, and Measure views.
- Graph View enables real-time plotting of mathematical results.
- Roll View displays time-domain waveforms of acquired data.
- Measure View provides statistical analysis of traces.
These views offer multi-dimensional insight into test results, making data interpretation and debugging more intuitive.

Efficient Remote Programming and Control
Based on an advanced SCPI command set, the SMM3000X supports USB and LAN interfaces for seamless PC connectivity and automation. Users can operate the instrument via a built-in web interface or implement deep custom control using SCPI scripting. In addition, TCP/IP Socket communication is supported for flexible network-based test control and integration into automated test systems.

The SMM3000X series is designed to meet the precision testing needs of third-generation semiconductors, advanced optoelectronic devices, and emerging materials, while also significantly accelerating development cycles for new energy batteries and high-density integrated circuits. By improving both test efficiency and measurement accuracy, provides a powerful foundation for new product development and innovation.
SIGLENT Launches New 8 GHz Digital Oscilloscope!
July 10, 2025 — SIGLENT has unveiled the enhanced SDS7000A/AP models, building on the success of its SDS7000A high-resolution digital oscilloscope series. The new models now feature bandwidth up to 8 GHz, a high-resolution 12-bit ADC, maximum 20 GSa/s sampling rate per channel, and a maximum memory depth of 2 Gpts/ch. New capabilities include 2.5G/5G/10GBase-T Ethernet Electrical Compliance Testing, MIPI-DPHY protocol analysis, Real-Time Spectrum Analysis (RTSA), Digital Down-Conversion (DDC), and upgraded CAN XL decoding.
2.5G/5G/10GBase-T Ethernet Electrical Compliance Testing
The upgraded SDS7000A series now supports full electrical compliance testing for 2.5G/5G/10GBase-T Ethernet, including critical parameters such as output drop, transmitter timing jitter, power spectral density, and MDI return loss. These features help ensure devices meet IEEE standards. Engineers can automatically generate IEEE 802.3-2018-compliant compliance test reports in HTML, XML, or PDF formats, including pass/fail status, threshold values, measured results, margin analysis, and waveform displays. This visually rich and data-driven reporting streamlines troubleshooting and product optimization.

MIPI-DPHY Compliance Testing
The SDS7000A series also supports MIPI-DPHY compliance analysis based on the CTS 1.0 specification. The oscilloscope captures HS-TX and LP-TX signaling on both data and clock lanes using its 12-bit ADC and ≥4 GHz bandwidth, combined with 5 GHz active differential probes. Eye diagram functionality is integrated for evaluating signal integrity, with automated configuration and report generation.

Real-Time Spectrum Analysis (RTSA)
Equipped with RTSA and digital down-conversion (DDC) technologies, the SDS7000A supports up to 1 GHz Real-Time analysis bandwidth. Advanced display modes include density plots, spectrum monitoring, and 3D visualizations. Compared to traditional superheterodyne spectrum analyzers, the SDS7000A offers higher bandwidth and faster signal acquisition — ideal for capturing transient events in 5G NR, 4G LTE, and Wi-Fi.

Integrated Vector Signal Analysis (SigVSA)
The SDS7000A features SigVSA vector signal analysis software, allowing direct signal analysis from DDC output without external equipment. It supports demodulation of signal types ranging from basic BPSK to complex wideband signals, such as those in 4G LTE, 5G NR, IEEE 802.11b/a/g/n/ac/ax/be standards, and 4096QAM. Both real-time and offline waveform analysis are supported, providing flexibility for laboratory and post-processing workflows.

Enhanced CAN XL Decoding Support
The SDS7000A series oscilloscopes provide comprehensive CAN protocol testing capabilities, with full support for CAN XL decoding in addition to CAN/CAN FD, enabling seamless coverage of automotive bus systems from low-speed diagnostics (10 kbps) to high-speed domain control (20 Mbps). The instrument supports both low-power and high-speed modes, making it well-suited for automotive and industrial control applications. The oscilloscope features 16 total channels (4 analog and 12 digital) for synchronized decoding and comprehensive fault analysis, including collision detection and signal reflections.

The SDS7000A also supports Wake-on-LAN (WoL), enabling users to remotely power up the instrument via Ethernet — ideal for automated test environments where physical access is limited.
With these cutting-edge features, the SDS7000A/AP oscilloscopes provide a powerful and versatile platform for engineers in data centers, wireless communications, consumer electronics, and automotive applications.





